120KW 4mm Wire Continuous Annealing Electric Heat Treat Furnace
3-wire Continuous Annealing Furnace Electric Heat Treat / Treatment
Furnace For Low Carbon Steel Wire
Technical parameter
1 Effective Heating Length: 20m*3 wires; It has preheating section,
heating section and holding section. 2 Effective Cooling Length: 8m*3 wires; 3 Heating power: 120KW (1-100% adjustable) 4 Temperature Control Zones: 6 Zones 5 Temperature Control Method: PID SCR Control Shanghai Guolong
temperature controller with over-temperature alarm； 6 Temperature Control Accuracy: ≤±2℃; 7 Furnace wall temperature: 45℃+Room Temperature; 8 Empty furnace power consumption: ≤18%; 9 Max working temperature: 1000℃; 10 Cooling water in cooling section: Recycling. For 24-hour work, a
cooling tower is recommended outside the workshop. 11 Furnace lining: furnace side and furnace roof adopt full fiber
structure; 12 Heating element: 0Cr21AL6Nb 13 Product: φ1-3mm stainless steel wire;
|
2. Construction heat treat/ treatment furnace /steel wire annealing furnace
Continuous steel wire annealing furnace is mainly composed of
furnace body, stainless steel pipe, heating
elements and fixing devices, electrical control system, and furnace
temperature automatic control system.
furnace body
2.1 Furnace shell:heat treat/ treatment furnace /steel wire annealing furnace
The outer wall of the furnace welded with Q235 plate with the
thickness of 3 mm.
It welded by 10 # section steel and 8 # section steel. The furnace
has the advantage of firm
structure, reliable and durable performance.
2.2 Furnace lining: heat treat/ treatment furnace /steel wire annealing furnace
The furnace lining is all-fiber structure. It adopts high-quality
high-temperature refractory
fibers, standard stainless steel round parts and scientific and
reasonable mounting method.
The aluminum fibers are pre-compressed into blocks (compression
gravity: ≥230Kg/m3 ) and
then fixed to the furnace body by round stainless steel parts. The
installation thickness of the
insulation material is ≮350mm. The structure has low heat
conductivity, strong anti-shock capacity, and anti-erosion.
The aluminum silicate fiber resists a maximum temperature of 1200℃.
The material of round steel is 1Cr13 round steel.
The lining has the effect of rapid heating and heat preservation.
The bottom is made of heavy refractory brick and mullite brick.
The expansion joints of refractory bricks are retained in masonry
to
prevent the expansion damage of lining when heated. Every 400 mm,
a shaped brick is used to fix stainless steel pipes (the wire mesh
inside the shaped brick prevents the cracking of the shaped brick
leading to the deformation of the stainless steel pipes). The two
sides
of each shaped brick are fixed with stainless steel splints.
1.3 Furnace body heating element:
The heat treatment furnace employs high-quality high-resistance
alloy material 0Cr21AL6Nb which is
processed into corrugated resistance bands. They are installed on
the bottom of the furnace
body to ensure that they are not damaged during processing. The
furnace has 6 heating zones.
The arrangement of heating elements corresponds to that of heating
zones. An independent
heating group is arranged in each heating zone. All lead-out rods
are made of φ16 0Cr25AL5
material. The special industrial chucks are used for lead-out rods
to ensure firm and reliable wiring.
1.4 Heating elements
The heating elements adopt high quality high temperature alloy belt
in order to meet long term
use at the temperature of 950 ℃. The furnace lining adopts aluminum
silicate refractory fiber.
The furnace is equipped with 3 stainless steel tubes for wires
going through. The specification
of the tube is Ø32*3, 20.5 meters length. The tube material is
310S(Cr25Ni20Si2)which has
the advantage of durability at high temperatures. Each pipeline is
equipped with protective
gas joint. The cooling groove at the pipe outlet is provided with a
sealing connecting device.
The inlet is equipped with guide device to ensure that the wire
runs in a straight line in the
pipeline. And the thermal expansion device of the pipeline is also
equipped in the furnace.
1.5 Cooling tank
The cooling tank is made of 5 mm thick iron plate by pressing and
welding, and the frame
is welded with 10# and 8# Q235 steel. There are 3 stianless steel
tubes sealed and welded
with heating tubes. The stainless steel tube material is 304
(1Cr18Ni9), and the diameter
is Ø32*3. The tank is equipped with inlet and outlet water to
ensure rapid cooling of annealed parts.
The effective cooling pipe length is 8.5 meters.
1.6 Nitrogen: provided by customer itself;
1.7 Temperature control system
Temperature control: the furnace adopts Shanghai Guolong
intelligent temperature controller
to control the temperature which has self-tuning function to
calculate the ideal PID parameter
and achieve temperature stability. The temperature controller has
the functions of over-temperature
alarm and thermal couple breakage protection.
The heating loop adopts the SCR and trigger control. The output
heating power can be changed to
achieve temperature control.
The over-temperature alarm system is sound and light alarm which
ensures the safety of workpieces
and equipment in furnace.
All main control devices, such as AC contactors, fast fuses,
intermediate relays, stroke switches,
operation switches, buttons, signal indicators, and operation and
display devices are the brand of
CHINT. heat treat/ treatment furnace /steel wire annealing furnace
3.Supply scope of heat treat furnace
| No. | Item | Q’ty | Remark |
| 1 | Furnace body | 1 set | |
| 2 | Heating elements | 1 set | Resistence belt and resistance wire |
| 3 | Temperature control system | 1 set | |
| 4 | Temperature controller | 6 pcs | |
| 5 | Compensation lead wire | 200meter | |
| 6 | Thermal couple | 6 pcs | K type |
| 7 | Guide roller device | 30 sets | |
| 8 | Cooling tank | 1 set | |
steel wire continuous annealing furnace picture:
