CAB Electric Aluminium Radiator Brazing Furnace 1200 - 220 -
12000MM with Gas
Application
The aluminium radiator brazing furnace is used to braze aluminum
heat exchangers such as radiators, intercoolers, evaporators,
and heater radiator under protective nitrogen atmosphere. The flux
used is NOCOLOK flux.
Equipment Advantages
1) The CAB aluminum radiator brazing furnace adopts high
performance porcelain fiber cotton material for heat preservation
purpose.
The furnace is able to rise to 630℃ from the ambient temperature in
around 2 hours.
2) The muffle of the brazing oven is once-formed by the large size
bending machine, and is made from Sweden 316L steel plate and
304 steel plate. 10M muffle is formed by one-time bending, and only
there is one v-slot at the bottom of the muffle. The one-time
forming muffle could reduce the misshapening effect at welding and
also deformation at the heating process.
3) The zones of the furnace are divided based on upper, lower, rear
and back area. The heating power is adjusted through PID
regulator so that the furnace could achieve an ideal temperature
uniformity of ±1℃. The brazing area could achieve a temperature
uniformity of ±2℃ so that it could meet the brazing requirements.
4) The temperature controller has the PID regulation function to
achieve a smooth temperature rise. Also the temperature controller
has the over-temperature alarm. The mesh belt is steplessly
regulated through the inverter. The driving mechanism is started up
in
the acceleration manner, and stopped in the deceleration manner to
reduce the tension of the mesh belt.
5) the aluminum radiator brazing furnace (or called as CAB furnace)
has a complete control system integrating intelligent control,
alarm and protection system. The real-time temperature recording
function provide the process data of different products.
6) The area of the fluxing chamber which contacts the flux is made
of stainless steel material. The two side walls of the fluxing
chamber are both set with an observation window to observe the
fluxing performance. The fluxing nozzles have a 90º fan-shape
spraying to prevent nozzle blockage. There is a filtering net for
recycling the flux to prevent damage to the fluxing pump.
7) The dry air cooling room is set with a slag cleaning chamber.
There is a side door of the slag cleaning chamber for allowing
the worker to clean the flux slags. In comparison to the
traditional water cooling chamber, the dry cooling room don’t have
the risk
of corrosion because of water and deformation of the chamber
because of cold and heat. There is no need for cooling water.
8) power at temperature rising stage: 100%; power at the brazing
stage: ≤60%
General Parameters
| Mesh belt operation surface height (to the ground): 900mm |
| Mesh belt speed: 300～1200mm/min (inverter control) |
| Effective working size: 1200mm(width)×220mm (height) |
Drying oven technical parameters
Function: the parts are well dried by the drying oven, and the
dried parts are an important precondition of a high quality brazing
process. The drying oven is an important parts of the aluminum
radiator brazing furnace. The drying oven works with gas so as to
save operational cost for the overall CAB brazing furnace line.
Technical parameters of Drying Oven
| Ovearll dimension: 7000mm(L)×2300mm(W)×2400mm(H) |
| Outer layer: steel plate, Q235, δ=6mm |
| Inner layer: stainless steel plate, δ=3mm (inner layer and air
returning hood) |
| Heat preservation layer: silicate aluminum fiber |
| Ground foot: 100×50 channel steel |
| Hot air circulation fan: 5.5KW, 4-grade, 2 sets; |
| Temperature sensor: K type (temperature controller controlling the
air/gas proportional valve) |
| Max design temperature: 350℃(service temperature:180～250℃); |
| Heating element: stainless steel U-type heating tube; |
| Heat source: 2 natural gas burners (2 zone control); |
| Single burner gas consumption: 13Nm3/h～33.8Nm3/h； |
| Burner output power: 130-338KW; |
| Temperature control: PID controller to control air-gas proportional
valve; |
Parameters of Brazing Oven
To save electricity consumption, the furnace adopts natural gas
heating to preheat the furnace to a temperature of 500℃, and leaves more time for brazing. The brazing oven is the key
parts of the aluminium radiator brazing furnace line.
| Furnace type: mesh belt conveyance furnace |
| Overall dimension: 10000mm(L)×2070mm(W)×1800mm(H) |
| Max design temperature: 700℃ |
| Heating element: spiral shape resistance wire |
| Heating power: 230KW |
| Heating zone: 3 zones, 6 points |
Temperature control: intelligent temperature controller with PID
regulation; PLC control |
| Temperature rising method: direct temperature rising |
| Effective size: 1200mm×220mm (including brazing fixture) |
